SPIG Air Cooling Systems

SPIG Cooling Tower Replacement Parts

SPIG Wet Cooling Tower Parts

SPIG Water Cooling Tower ReplacementAs a leading worldwide supplier of SPIG™ cooling system solutions, we provide comprehensive after-sales services including operational support, maintenance, training, upgrades and replacement parts.

Our replacement components for wet cooling towers are reliable and proven to keep your equipment operating at optimum efficiency levels, regardless of original manufacturer. Quality components are available for quick delivery from a worldwide network of service locations to provide you with continuous and safe plant operation.

Explore Our SPIG Wet Cooling Tower Replacement Parts:

 

Fills

Film fills

SPIG wet cooling system film fill turns water droplets produced by distribution nozzles into a thin film for highly efficient cooling by producing a large area for effective heat transfer and evaporation.

We use high-quality materials to help extend the lifetime of the cooling tower and reduce the frequency of component replacement.

In applications with particularly dirty process water, our SPIG LC fill type was developed to achieve the best compromise between high-thermal performance and water containing higher amounts of contaminants.

 SPIG Fills Replacements

Film fill protection device

Our film fill protection device is designed to protect against damage to spray nozzles and the film fill upper layer in applications where water contains high levels of contaminants such as sand or debris. This device is composed of PVC-extruded pipes and PP spacers to be assembled onsite, and positioned on the upper surface of film fill. It is available in varying lengths to fit into any cooling tower dimension.

Film Protection Layer

Splash fill

We provide a wide range of SPIG splash fill components to facilitate heat transfer capability by maximizing water/air contact. Our wide range of splash fill components were developed based on extensive field experience, particularly with water which is prone to clogging, such as sea and geothermal water.

 Splash Fills Specs

 


Distribution Nozzles

Distribution NozzlesEffectively designed distribution nozzles help ensure a uniform delivery of water over the fill. SPIG ECOJET and NEW STATIC distribution nozzles have been developed after extensive and successful performance test results and are proven in many installations.

Our ECOJET and NEW STATIC distribution nozzles provide versatility, high reliability and outstanding performance, and can be manufactured with V2 as per UL-94 standards for self-extinguishing properties.

Distribution Nozzles - Spec Chart

 


Drift Eliminators

Installed above the distribution level, drift eliminators play an important role by capturing water droplets entrapped in the air stream that otherwise would be lost to the atmosphere.

Current SPIG drift eliminator designs have been developed and refined through the years based on field applications and performance testing

Drift Eliminators Specs

 

 


Noise Attenuation System

Typical noise abatement devices are available as baffles at the air inlet and/or on top of fan stacks, mechanical equipment coffins, and low-noise cladding made from FRP. In addition, our Impact Attenuation Wave (IA-Wave) noise attenuation system can be installed to reduce high-frequency noise produced by water fall from fills to water in the basin. This system consists of special inclined profiles adequately spaced to allow for quick drainage of the falling water. The system is composed of high-quality PVC-extruded elements packed by PP spacers and is installed over the water level in the basin, typically on FRP beams.

Noise Attenuation Wet Cooling Tower Part

 


 

Air Inlet Louvers

Air inlet louvers are available to reduce the potential for debris to enter the basin at the cooling tower air inlet. The device is also helpful to avoid the risk of algae and bacteria propagation caused by direct sunlight shining on the basin water. Constructed with PVC light gray thermoformed panels in a standard width of 65 mm, we can also customize panel dimensions to fit most cooling tower applications and FRP support elements.


Air Inlet Louver Replacement Part

 


Multi-Row Bundles

For hybrid cooling towers, we can provide heat exchangers with a multi-row bundle configuration. Our controlled aluminum finning process is adaptable for G or L fin configurations with different FPI and pipe diameters from 1 in. to over 2 in. This provides the flexibility for a wide range of applications.

Multi-Row Bundles Wet Cooling Systems Replacement Parts

 


Fan Stacks

A wide range of fan stack diameters and heights can be supplied through reliable partners utilizing SPIG proprietary molds. Flanged fan stack connections are typical, but an overlapped design can also be supplied when requested. Typical material is standard polyester resin or fire-retardant FRP with FSI<25 as per ASTM codes.

 


Other Accessories

We have developed many other exclusive components to facilitate installation or reduce transportation costs, such as spacers for FRP structures and sleeves, FRP main column supports, and basin shims. We can also supply:

  • All mechanical components for electric motors, gear boxes, driving shafts and fans
  • Backstop devices, lubrication systems, and sensors to monitor mechanical components
  • Firewalls to prevent fire propagation between cells
  • Ladders, platforms and stair cases
  • UNICO cooling tower remote monitoring system
  • FRP risers to feed water in each cell, valves
  • Vacuum systems, dampers and mixing devices for dry section of hybrid cooling towers
  • Fire-fighting system
  • Cleaning system for heat exchangers